A Few Simple Lessons in Designing Reliable 3D Flex

There is an old and familiar adage that goes something like this: "If the only tool in your tool chest is a hammer, you tend to see every problem as a nail." We all have a tendency to stick close to the familiar and use the tools we know to create solutions to problems confronting us; we’re only human. Unfortunately, using only familiar tools limits our ability to come up with optimal or even superior solutions. Hopefully, what follows will help you avoid some of the traps conventional wisdom doesn’t always give guidance on.

But first, having written extensively over the years about flexible-circuit technology, I still try to find fresh ways to think about flexible circuits and their construction and use. In the process of thinking about what I might say here, a fun book I read in high school more than half a century ago came to mind. The title of that book is Flatland: A Romance of Many Dimensions by Edwin A. Abbott [1]. In full disclosure, and as one might guess from the extended title, the book is not about geometry but is a rather entertaining read. I found it to be a useful book for stimulating thought.

Fjelstad-Fig1-Flex007Mag-Jan2019.jpg

Figure 1: View of an iPhone's internal electronic elements layout upon opening the device (folding interconnections between the halves enabled by flex circuits). (Source: Tech Insights)

In the book, almost every male character in Flatland has two major dimensions—X and Y—and many possible sides (thus, they have area), but they can only be perceived as lines when looked at from the reference of the planar world in which they exist. Women, on the other hand, are depicted as being basic lines, and are required to make noise as they move about through Flatland should they be encountered head on and appear as a simple point. The protagonist (a square) encounters both Lineland and Pointland, but the encounter with a sphere from Spaceland is where the entertainment really begins. Trying to convince others of another dimension is no mean task, one learns. Many humans are resistant to accepting the teachings of science. The book proved useful over the years to a number of prominent scientists (including Carl Sagan) seeking to help the layperson understand the multidimensional space they envisioned and were attempting to explain.

That function of envisioning the not-always-easily perceived is summoned here, but for a much less complex purpose than defining space and time. My specific purpose is, “How to tease a three-dimensional circuit from a two-dimensional copper-clad panel and do so reliably?” That should be job one in nearly every flex-circuit design. So how does one carry out the task and make 2D into 3D reliably? Here are some suggestions. Be warned in advance that there are no pat answers to the question posed. Each design inevitably has its own set of requirements and challenges, but there are a few steps that are common:

1. Define the end-product shape, size, and volume: This is the primary constraint for the design—the canvas for the painting. An individual or team has the job of defining the shape and volume of the product. Often, that job is constrained in some manner either by limitations of space where the electronics are going to be put to use or by a mandate from marketing or management. Steve Jobs, it has been said, was intimately involved in the design of the iPod and iPhone in terms of the size and shape and other design features along with its functionality. He did not execute the design and manufacture by himself, however. He created a significant challenge for designers, and flexible circuits were vital to achieving the goal. In fact, the use of flexible circuits was arguably crucial to making it happen as they were indispensable to the interconnection of the various high-density connecting elements of the electronics in the product (Figures 1 and 2).

Fjelstad-Fig2-Flex007Mag-Jan2019.jpg

Figure 2: Flexible circuits are plentiful inside the iPhone and vital, enabling elements of the phone’s construction. (Source: Tech Insights)

2. Identify all components and make selections carefully: Many years ago while working for a major aerospace company, I was part of a group tasked with making a circuit that needed to fit in a very small predefined space. To say that it was difficult was to understate the case. The devices chosen for use with the design were rated for reliability, but they were very large. It was as if someone had measured the volume of each of the individual components and their collective volume, and, also knowing the volume of the space available and seeing they matched, they decided it was possible. It wasn’t quite that bad but it seemed that way. Moreover, the design chosen was a rigid-flex, which was not very common at the time and the processing was not well understood. The product was built and had several overlapping flex arms designed to interconnect to bulkhead connectors inside the space. Trying to assemble the circuit was a nightmare, and because there was little additional length on the arms, many of the circuits broke during the assembly process. It was eventually solved by a combination of selecting different components and getting some relief on the size of the box by making it slightly larger. The takeaway is that the early decisions can have a knock-on effect of significance.

3. Use paper doll mockups of the proposed layout: Available CAD tools can lay out circuit patterns and allow them to be modeled for interferences in the application. However, a simpler method—at least for first-pass approximation—is to create a paper model of the assembly design to see what traps might lie in the road ahead. This will be instructive in determining roughly how much extra length might be required to provide a service loop, which not only facilitates assembly but also creates some intrinsic strain relief in the circuit. Later, when the layer counts that might be required and the construction are defined, it can be repeated using materials of similar thickness and stiffness to the anticipated construction. This will expose any previously unforeseen potential for buckling or kinking of the circuit during assembly.

4. Use no right or acute angles in the flex circuit outline: Stress risers are anathema in nearly every mechanical design, and with flexible circuits having a foot in an electrical, electronic, and mechanical world, stress risers are no less important. The first and arguably most important thing one must do is to make sure that right or acute angles be avoided everywhere possible in the circuit outline. The interface between the rigid and flex circuit is one spot where it is not really possible, and this should ideally be dealt with by providing some strain relief at the interface. Commonly, this is a bead of some resin or elastomer along the edge. I have seen failures occur at this interface, and I suspect other veterans of flexible circuits have as well over the years.

This was not meant to be an exhaustive treatise on the topic. As I am certain every other flex circuit engineer has, I have a number of anecdotal experiences that involve nuanced elements of the design and assembly process that have resulted in failures, but these are some important ones in my opinion. I would add that when you experience failure—and it is likely you will at some point—embrace the moment. These are teaching moments and lessons that will not be forgotten.

References

1. Flatland: A Romance of Many Dimensions by Edwin Abbott Abbott, 1884, available for free download at Project Gutenberg.

Further Reading

For more detailed discussions on this and other flex circuit topics, download your free copy of Flexible Circuit Technology, 4th Edition at www.flexiblecircuittechnology.com.

Joe Fjelstad is founder and CEO of Verdant Electronics and an international authority and innovator in the field of electronic interconnection and packaging technologies with more than 150 patents issued or pending.


Editor's Note: This article originally appeared in the January 2019 issue of FLEX007 Magazine, click here.

Back

2019

A Few Simple Lessons in Designing Reliable 3D Flex

04-11-2019

We all have a tendency to stick close to the familiar and use the tools we know to create solutions to problems confronting us; we're only human. Unfortunately, using only familiar tools limits our ability to come up with optimal or even superior solutions. This article will help you avoid some of the traps conventional wisdom doesn't always give guidance on.

View Story

Flexible Thinking: Ways to Conserve Flex Circuit Material in the Design Process

02-25-2019

In summary, the decisions made by the flex circuit designer when laying out a flex circuit will have an impact that lasts the entire process. By considering how the circuit might fit onto a panel before submitting the design to a manufacturer, it may be possible to save a considerable amount of material and money.

View Story

Flexible Thinking: A Few Simple Lessons in Designing Reliable 3D Flex

02-11-2019

There is an old and familiar adage that goes something like this: “If the only tool in your tool chest is a hammer, you tend to see every problem as a nail.” We all have a tendency to stick close to the familiar and use the tools we know to create solutions to problems confronting us; we’re only human.

View Story
Back

2018

Flexible Thinking: Achieving Continuous Flexible Circuit Innovation

12-07-2018

Since their introduction, flexible circuits have continued a steady climb from relative obscurity to center stage in the world of electronic interconnections. Today, they are among the most popular choice for solving challenging electronic interconnection problems. Those who use this technology on a regular basis are familiar with the many reasons for the popularity of flex.

View Story

Flexible Thinking Redux

07-02-2018

Flexible circuits are known by a few different names depending on one’s global location and language: flexible printed circuits, FPCs, flex circuits, flexi circuits, flexibles, bendables and a few others that are application-specific such as flexible heater circuits and controlled impedance cable constructions. While flex circuits are an original and foundational interconnection technology for electrical and electronic products (one of the first patents for electrical interconnections, issued at the turn of the last century, was arguably a flexible circuit), over the years there have been several forays into technological extensions of the basic idea.

View Story
Back

2017

Flexible Thinking: The Benefits of Employing a Standard Grid Pitch in Design

03-31-2017

The industry at large needed to jump on the learning curve and overcome its fear of the unknown. One of the most vexing concerns at the time (an arguably still today) is that terminations beneath the area array package were unseeable. Given the fact that then, as today, solder joints were a major cause of failure, there was much consternation over the quality of the joints.

View Story
Back

2016

Flexible Thinking: Process Engineering—PCB Manufacturing’s ‘Delta Force’

05-11-2016

Process engineers serve a vital function on the front line of printed circuit manufacturing. They are often, if you will, the “Delta Force” that subdues and controls that which is one of the mortal enemies of manufacturing…process variation.

View Story
Back

2015

3D Printing in Electronics - A Perspective

01-14-2015

Knowing the value of a product or technology is key to making the right decision. Appreciating the value of an element of business is evermore important as the rate of change surrounding an industry accelerates. This brings us to one of the current buzz subjects in our industry: 3D printing. Understanding what it is and what its value is to a company and that company's ability to improve its place in the industry is vital.

View Story
Back

2013

The E.I. Files: The Electronics Industry's Black Swans

07-31-2013

First proposed in 2007, there is a potential electronics industry "black swan" technology quietly being developed and refined. It is one that could greatly and positively impact, at once, the cost, reliability, and environmental friendliness of electronic manufacturing by simply eliminating the soldering process.

View Story

Flex Circuits and Photonics: A Pairing for the Future, and the Here and Now

04-17-2013

Photons are making continuous headway into the world of electronics. One thing that the basic data carriers (electrons, microwaves and photons) have in common is that flexible circuits are being increasingly looked to for help in managing their data transmission function.

View Story
Back

2012

Stretching the Limits of Flex

11-29-2012

Those steeped in flexible circuit design and manufacture for any length of time fully appreciate the long list of benefits that only flexible circuits can offer. Some of the most fundamental benefits of flex circuit technology have been exploited since the earliest days of the technology. Joe Fjelstad explains.

View Story

Flexible Thinking: Circuit Flexibility (and How to Achieve it)

10-04-2012

The most common interpretation of the word flexible, as applied to the flex circuits that the industry currently makes, is something capable of being bent repeatedly without breaking. Joe Fjelstad discusses a few other definitions of flexible that are worthy of consideration when using the term, for their ability to unlock new thinking patterns relative to what is flexible.

View Story

Technology Roadmaps: Thoughts and Observations

09-26-2012

If one is without a sense of the direction their technology is headed, odds are that they will sooner find themselves on the road to ruin than the road to success. A technology roadmap is a critical tool in helping a company make informed decisions. By Joe Fjelstad.

View Story
Back

2011

Something Old, Something New: Stretchable Circuits and Elastronics

10-13-2011

The stretching of circuits to alternately increase and decrease the length of a circuit has proven useful for electronic products and assemblies for years. Stretchable circuit technology and elastronics are poised to take on challenges that cannot be easily met by flexible circuit technology alone. Keep them in mind next time you find yourself in need of a little more "spring" in your design. By Joe Fjelstad.

View Story

Stretchable Circuits: The Emergence of "Elastronics"

07-14-2011

The stretchable circuit is an interesting and promising new branch on the flexible circuit tree. The stretching of circuits to alternately increase and decrease the length of a circuit has proven useful for many years. The European Union has funded research in this area through such initiatives as the STELLA project.

View Story
Back

2010

Flexible Thinking: An Alternative Approach to Rigid-Flex Assembly

11-18-2010

The fundamental approach to manufacturing rigid-flex has remained constant for the 40-plus years of rigid-flex history. But is there a better way? What if one could produce a circuit that was rigid throughout the manufacturing process and only become flexible in the final step? In other words, what if one could make a rigid circuit assembly, flex?

View Story

Reasons Why The Flex Market Continues to Shine

10-07-2010

According to IPC market statistics, flexible circuits continue to be the brightest sector of the overall printed circuit market. The reasons for this are many but, at the end of the day, it generally boils down to the fact that flexible circuits are an excellent way to solve interconnection challenges in a cost-effective way.

View Story

Flexible Thinking: Flexible Structures for Data Transmission

08-12-2010

Flexible circuit cables offer some significant advantages for facilitating the movement of data between elements of a system that must also be moved or flexed. However, there is a balancing act involved and there is more than one master to be served to create a system that is robust, reliable and easily manufacturable.

View Story

Flexible Thinking: Supporting Components on Flex Circuit Assemblies

07-21-2010

With proper planning, stiffeners can be designed to aid assembly through the designed manufacture of a flex circuit that can be handled as if it were a rigid circuit board. Such constructions can be accomplished by using any one of several methods.

View Story

A Simple Approach to Flex Manufacture, Assembly

04-29-2010

Flexibility, the single attribute that makes flex so attractive, also makes flex circuits more difficult to build. What if we could produce a circuit that was rigid throughout the entire manufacturing process and only become flexible in the final step?

View Story
Copyright © 2019 I-Connect007. All rights reserved.